CM040I assault rifle replica (ASCU version)
The family of CM replicas based on popular Russian assault rifles has been complemented with a new line - modified with a range of 'tactical' accessories, increasing ergonomy and possibilities of configuration of this classical design.
The replica has been perfectly matched, there are no backlashes here, the product was thoroughly finished in mat, black colour. Steel, aluminium, alloy of Zn and Al as well as polymers were used in the construction process. The receiver, the dust cover, the trigger guard and the fire selector were made of steel. The front RIS rail system was made of aluminium, whereas the pistol grip and stock were made of plastic.
The replica has got a telescopic SF type stock of regulated length. In the place of a standard front guard, the complete conversion with 22mm RIS mounting rails was applied here, which allows to equip the rifle with additional accessories. Moreover, the replica was equipped with both-sided charging handle and with an ergonomic SAW pistol grip. On the right side there is a fire selector, distinctive of AK.
Disassembling of the replica and mounting additional accessories is eased by the design itself based on pins and levers - similar to the real steel and other AK replicas in the popular standard VFC. The outer barrel ends with a 14mm left-hand thread, where the flash hider was mounted. The replica's battery is located inside the stock and its slide (included in the set).
The replica is driven by a very reliable and easy to upgrade gearbox v.3 with a strengthened frame. A set of steel racks , steel 7mm slide bearings, a strengthened piston and spring slide were mounted inside. Efficiency is ensured by a 370mm long inside barrel and a tight metal Hop-up chamber.
The replica goes together with a plastic hi-cap P-MAG magazine with capacity of 500 BBs
The ASCU is a two-part electronic module ( the control module and the sensor module ) which, upon being installed in the Airsoft replicas, significantly improve their operation. The traditional joint module was replaced with a sensor module which monitors the actual position of the piston thread-wheel, the firing mode selector lever and the trigger. The gathered information is sent to the control module – in which the software located in the processor analyzes it and controls the replica’s motor with the use of the MOSFET active break.
ASCU Gen. 3+ includes the following upgrades:
- added polymer padding to the circuit boards, protecting them from damage during installation
- obsolete short-circuit software removed, making shots in semi-auto much faster
- every pull on the trigger results in a single shot, new system prevents any double-shots
- new cut-off lever and selector plate designed specially for the ASCU
- new, thicker wires
- no need to dremel or modify the reinforced gearboxes.
The ASCU improves the operation of a V.3 gearbox and makes that the replica equals the more expensive replicas and the more sophisticated PTW class replicas. The ASCU system monitors the operation of the replica no matter the speed of squeezing the trigger and is responsible for the full cycle of the piston’s operation, both in the semi-automatic and full automatic firing modes. The piston stops in the starting position after each shot.
The ASCU is equipped with the Low Drain Protection system which is specially designed to secure the lithium-polymer (LiPo) batteries from being damaged.
In case of any emergency, the ASCU stops the firing mode in the replica and, therefore, secures the inner elements from further damage.
The ASCU is easy to install in the replica which is equipped in the V.3 gearbox. Most of the models does not require the modification of the airsoft rifle’s original parts. Yet, in some cases, some minor changes may have to be introduced – thanks to this the installation process will be completed without any problems.
The set includes:
- battery charger
Replika karabinka CM040I (ASCU version)
It is the spped of bb, while its leaving the innerbarrel of replica. This speed is measured in FPS (Feet Per Second).
1 FPS = 0,3 m/s
1 J = 99 m/s
1 J = 326,7 FPS
|Propulsion / Powered by:|
Indications v2, v3, v6 does not mean the level of advance, but only shape of gearbox skeleton which was used and selected by the manufacturer depending on the capabilities of the body of the replica. For example, a models of the M4/M16 family, MP5, have a v2 gearbox, while the AK family have gearbox v3.
|Type of fire:|
Steel + aluminum + plastic
|Diameter of bearings in GB [mm]:|
The length of the replca is measured between the two most distant points of each other. Different models have several of these values, because of its design allows to increase or decrease it length (eg. folding stock or extended flash hider).
|Inner barrel length [mm]:|
This is a value that includes the weight of the replica, magazine and other accessories that are include in set without a battery, charger, cleaning rod, etc., etc.
|Battery Voltage [V]:|
|Battery Capacity [mAh]:|
Battery capacity determines the time, which it accumulated enough energy to work gearbox. The greater capacity, then replica will shoot longer.
rechargeable battery is characterized by high efficiency
current-carrying capacity, but there are disruptive effect on memory.
Should be unloaded and loaded in the full cycle, ie, it is recommended
to fully discharge, and after unloading must charge the battery
immediately without leaving it for a long time in a discharged state.
|Magazine capacity [pcs]:|
Hop-Up system is used for overclocking bb during the shot (putting it in rotation), through which, it extends its flight path. Acting laws of physics make that bb lift up, while the gravitational force take it down. Appropriate adjustment of Hop-Up, will compensate for these two factors, which result in long and straight flight for longer distance and be greater focus shot (to improve accuracy).
Blow back is a simulation system of the cocking lever - it imitates the work of it as the equivalent sharp. This system raises the realism and adds a lot more experience during shooting.